Инструкция по эксплуатации Panasonic EW1211W835
Страница 4
Внимание! Текст в этом документе был распознан автоматически. Для просмотра оригинальной страницы Вы можете воспользоваться режимом "Оригинал".
c
c
remaining
waterafteruse.
operating
the
unitwithoutwatermayresultina
malfunction.
1.
Attach the nozzle and the tank
firmly onto the unit (Fig.5).
2.
Open the cap of the water tank,
hold the unit so it is level, and fill
the tank with cold or warm water,
not hotter than 40“C (Rg.6).
•
Do
not
put
salt,
toothpaste,
powder,
or
other
chemicals
Into
the water tank.
•
Certain
liquid
mouthwash
may
damage
the
device
by
causing
the housing or the tank to crack.
When
using
mouthwash,
rinse
the tank arid main unit with wa
ter
immediately
after
use.
Be
especially
careful
when
wash
ing the hose connections at the
main unit and the tank.
CAUTION:
Never fill the tank with hot water!
The gumlines can be very sensitive
and can be easily damaged by hot
water.
3.
Close
the
cap,
making
sure
it
locks in place (Fig.7).
4.
Press the mode switch and select
the
desired
water
jet
inode.
The
mode
indicator
will
display
the
previously
selected
mode,
if
the
unit is not used for more than 30
days, or after the unit has been
fully
charged
from
its
fully
dis
charged state, the mode is initial
ized to its soft air-in jet water set
ting.
If you want to use
a
different mode,
press
the
mode
switch
until
it
changes
to
the
desired
setting.
Pressing
the
mode
switch
will
change the mode from soft air-in
to normal air-in to jet.
Mode and its indicator (Fig.8)
© Mode switch
Pressing
the
mode
switch
will
change
the
water
jet
setting
and
the
respective
mode
indicator
will
light up.
@ "Jet" mode
This
mode
is
for
removing
food
particles
trapped
between
the
teeth.
(D "Normal air in" mode
This
mode
is
for
removing
food
particles
and
for
massaging
the
gums
and
rinsing
between
the
teeth and gums.
® "Soft air in" mode
This mode is for gently massag
ing the gums.
Note:
When you use the unit for the first
time,
press
the
operation
switch
to
turn the unit on and test each of the
water jet modes with the tank filled
with water.
5. Insert the nozzle into your mouth.
• Bend over the sink and hold the
unit
in
an
upright
position
with
the
nozzle
pointing
toward
your
teeth.
6. Press the operation switch.
•
Close
your
mouth
slightly
to
contain the water spray.
•
The unit starts operating in the
mode selected in step 4 above.
•
Pressing the mode switch dur
ing use will change the mode.
• A fully filled water tank provides
approximately
35
seconds
of
use.
•
The ventilation hole in the rear
of the unit allows for easier wa
ter suction of the hose. (If the
unit
is
tilted
too
much,
water
may come out from the ventila
tion hole; this is normal.)
CAUTION:
• Do not turn the switch on before
putting the nozzle in your mouth.
• Do not hold the tip of the nozzle
firmly against the teeth or gums.
7.
Turn the nozzle wheel with your
thumb to reach all areas in your
mouth (Fig .9).
•
Keep
your
mouth
slightly
opened
so
that
the
water
can
flow out.
•
Systematically
rinse
all
teeth
and the spaces between them.
•
Make sure that you always hold
the device in an upright position
with
the
nozzle
pointing
up
wards. If you turn the device up
side
down,
no
water
from
the
tank will be taken in.
• Remember that rinsing the mouth
is
not
a
substitute
for
tooth-
brushing.
Brush
your
teeth
or
dental
prosthesis
immediately
after a meal for at least five min
utes and then use the device.
8.
After use, press the operation
switch to turn off the unit.
• Be sure to turn off the unit while
the
nozzle
is
still
inside
your
mouth.
CAUTION:
• This device is designed exclusively
for use in the oral cavity.
Never use it for rinsing or cleaning
other parts of the body (e.g., ears
or eyes).
•
During the first several uses, light
bleeding
of
the
gums
may
occur.
If
your
gums
are
healthy,
any
bleeding during use should stop in
one to two weeks. If bleeding per
sists after two or more weeks of
use, consult your dentist.
AFTER USE
(Fig.lO)
t.With
the
nozzle
still
attached,
open the cap of the water tank
and pour out the water.
2.
Switch on the device for a few
seconds
to
pump
out
any
re
maining water.
•
Always pour out the remaining
water and empty out the nozzle.
This helps to prevent contamin
ation
and
bacterial
growth
in
the remaining water.
3.
Turn off the device and return it
to the charger.
•
The charging indicator will light-
up.
4.
While
pressing
the
nozzle
re
lease
button,
remove
the
nozzle
from the unit and place it on the
nozzle stand.