Yamaha RX-V665 - Инструкция (Страница 37)

35
En
English
INTR
ODUCTION
AD
DITIONAL
INFORMA
T
ION
APPENDIX
PRE
P
ARA
T
ION
BA
S
IC
OPERA
T
ION
AD
V
ANCED
OPERA
T
ION
You can connect a Yamaha Bluetooth wireless audio receiver (such as YBA-10, sold separately) to the DOCK terminal of
this unit and enjoy the music contents stored in your Bluetooth component (such as a portable music player) without
wiring between this unit and the Bluetooth component. You need to perform “Pairing” the connected Bluetooth wireless
audio receiver and your Bluetooth component in advance.
Note
• This unit supports A2DP (Advanced Audio Distribution Profile) of the Bluetooth profile.
“Pairing” refers to the operation of registering a Bluetooth
component for Bluetooth communications. Pairing must
be performed when using a Bluetooth component with the
Bluetooth wireless audio receiver connected to this unit
for the first time or if the pairing data has been deleted.
y
• You only need the pairing operation for the first time that you use the
Bluetooth component with the Bluetooth wireless audio receiver.
• Pairing requires operations on this unit and on the other component with
which Bluetooth communications are to be established. If necessary,
refer to the other component’s operating instructions.
■ Pairing the Bluetooth wireless audio receiver
and your Bluetooth component
1
Change the input source to “DOCK” using
OINPUT l / h (or hDOCK).
2
Turn on the Bluetooth component you want
to pair with and set it to pairing mode.
For details on operation of the Bluetooth component,
refer to its operating instructions.
3
Press nOPTION.
The option menu for DOCK input appears on the
video monitor.
4
Press oCursor n to select “Pairing” and
press oENTER.
“Searching” appears on the front panel display and
the pairing operation starts.
y
• To cancel pairing, press oRETURN.
• You can also start pairing operation by pressing and holding
FMEMORY on the front panel.
5
Make sure the Bluetooth component
recognizes the Bluetooth wireless audio
receiver.
If the Bluetooth have recognized the Bluetooth
wireless audio receiver, “YBA-10 YAMAHA,” for
instance, is displayed in the Bluetooth device list.
6
Select the Bluetooth wireless audio receiver
from the Bluetooth device list, and enter a
path key “0000” into the Bluetooth
component.
When pairing is complete, “Completed” appears on
the front panel display.
y
• The Yamaha Bluetooth wireless audio receiver can be paired with up to
eight Bluetooth components. When pairing is conducted successfully
with a ninth component and the pairing data is registered, the pairing data
for the least recently used other component is cleared.
1
Change the input source to “DOCK” using
OINPUT l / h (or hDOCK).
2
Press nOPTION.
3
Press oCursor n repeatedly to select
“Connect” and press oENTER.
After you execute “Connect,” communication with
the Bluetooth component is established. When the
connected Bluetooth wireless audio receiver
recognizes the Bluetooth component, “BT
Connected” appears on the front panel display.
y
• When you press oENTER on the remote control, the connected
Bluetooth wireless audio receiver searches and connects to the last
connected Bluetooth component. If the Bluetooth wireless audio
receiver cannot find the Bluetooth component, “Not found”
appears on the front panel display.
• To disconnect the Bluetooth wireless audio receiver from the
Bluetooth component, display the option menu again, select
“Disconnect,” and press oENTER.
4
Start playback of the Bluetooth component.
Using Bluetooth™ components
Pairing the Bluetooth™ wireless audio
receiver and your Bluetooth™
component
To ensure security, a time limit of 8 minutes is set for
the pairing operation. You are recommended to read
and fully understand all the instructions before starting.
DOCK OPTION
Connect
. Volume Trim
[ENTER]:Select
Pairing
[ ]/[ ]:Up/Down
[
[
Playback of the Bluetooth™
component